> Preparing CassingOpen both the cover Cassing by removing the four screws that are behind Cassing. Keep both casing side in a safe place.
> Replacing the Processor- Open the plastic cover that covers the socket on the mainboard processor.- Open the iron and the lever hook penutp meekan way upwards and then pull rod socket.- Insert the processor into the socket to maintain the state of socket handles and iron cover when entering the processor.- When entering the processor must pay attention to the correct orientation, there are special instructions to the processor and socket.- Push down the CPU and return the original stalk keposisi socket.- Place the heatsink on the CPU and plug socket correctly.- Power cable for the fan to the mainboard. Put socketnya usually exist on the processor / CPU just look that said PAN.
> Installing Memory- Open a socket cancing- Check the figures cetakkan RAM- Enter into the DDR SDRAM slot- Key / press back button
> Installing the MainboardReplace the back cover plate as the emergence of I / O port. Take the mainboard and put into Cassing. Position with bolt holes in the base mengepaskan. Then attach the bolts Mainboard.
> Replacing the hard driveWe use the hard drive is SATA type. Take the red wire. Barely the tip of one on the mainboard according to the position. Replace the hard drive in accordance with the place, then tighten the bolts. Connect the other end on the hard drive.
> Replacing the Optical Diskdo almost the same as installing hard drive.
> Install Data CableData cabling is easy. Installation for fitting, the part that no holes from the end of the cable must be fitted to the data that is not assigned to port pins.
> Install the connector to the Panel- Connect the connector to the panel thoroughly with Cassing.- The position of pin / leg depends on the mainboard connector (usually already available already written his name around the mainboard)
> Cable TidyIn order to not hit the fan connector and look neat, then the connector should be in trim. How to tidy up the gengan konector using clamps. Excess clamp on the piece by using cutting pliers. To turn on additional fans, plug konector konector powernya with power from the power supply box.
> Replacing the Processor- Open the plastic cover that covers the socket on the mainboard processor.- Open the iron and the lever hook penutp meekan way upwards and then pull rod socket.- Insert the processor into the socket to maintain the state of socket handles and iron cover when entering the processor.- When entering the processor must pay attention to the correct orientation, there are special instructions to the processor and socket.- Push down the CPU and return the original stalk keposisi socket.- Place the heatsink on the CPU and plug socket correctly.- Power cable for the fan to the mainboard. Put socketnya usually exist on the processor / CPU just look that said PAN.
> Installing Memory- Open a socket cancing- Check the figures cetakkan RAM- Enter into the DDR SDRAM slot- Key / press back button
> Installing the MainboardReplace the back cover plate as the emergence of I / O port. Take the mainboard and put into Cassing. Position with bolt holes in the base mengepaskan. Then attach the bolts Mainboard.
> Replacing the hard driveWe use the hard drive is SATA type. Take the red wire. Barely the tip of one on the mainboard according to the position. Replace the hard drive in accordance with the place, then tighten the bolts. Connect the other end on the hard drive.
> Replacing the Optical Diskdo almost the same as installing hard drive.
> Install Data CableData cabling is easy. Installation for fitting, the part that no holes from the end of the cable must be fitted to the data that is not assigned to port pins.
> Install the connector to the Panel- Connect the connector to the panel thoroughly with Cassing.- The position of pin / leg depends on the mainboard connector (usually already available already written his name around the mainboard)
> Cable TidyIn order to not hit the fan connector and look neat, then the connector should be in trim. How to tidy up the gengan konector using clamps. Excess clamp on the piece by using cutting pliers. To turn on additional fans, plug konector konector powernya with power from the power supply box.
0 komentar:
Speak up your mind
Tell us what you're thinking... !